Autoclaved Aerated Concrete Blocks are normally made by calcined gypsum, quartz sand, cement, lime, water, aluminum powder and cure with heat and pressure to finish in an autoclave. It is a green building product that helps to reduce weight as compared to ordinary concrete aggregates. We contractor usually named it as AAC Block and it is a well-known product if you wish to build a green building. Over the years AAC Block has been constantly increasing in demand in the construction industry of Malaysia. Consult us for your AAC blocks supplier Malaysia, to give you best advise on the specification you might require and also substitution of bricks for your projects.
Autoclaved Aerated Concrete There are many AAC block suppliers in Malaysia. Most of them having the common issue is that they need to pre-order the block and the ready stock is usually in a minimum amount. AAC blocks supplier Malaysia will always it good insulator against sound, heat, fire; resistant agent to mold, water beside it can be used as a structural building material for internal wall, external wall, roof, and floor. AAC lightweight block in Malaysia is also very popular because it allows you to build fast and easy to use where inexperienced workers or house owner can Do-It-Yourself (DIY) with proper instruction information given. Due to the raw materials and process of manufacturing of AAC by all the AAC block manufacturer in Malaysia, it is basically having high insulation against thermal. The steam curing process involves high pressure, and it the physical properties of these AAC are consisting of more than millions of tiny air pockets which are not connected to each other. The materials used to make AAC are sand, cement, aerating agent and lime, mixtures will be allocated by AAC blocks supplier in Malaysia to all the mold sizes and subsequently to form the lightweight AAC bricks, AAC blocks, AAC panels, and AAC lintels as a result of autoclave’s curing. Lightweight also mean you need lesser structural supports to be built, and mortar for joints of each blocks also lesser due to its reduced joints’ number (bigger of each block’s size than a conventional brick). It applies to the plastering and rendering too where cost savings can be achieved by having a dimensionally stable and accurate block, with also thinner plastering thickness. Heat insulation product by AAC brick supplier in Malaysia saves you in term of time, efforts and costs to install additional heat insulation materials.
Lightweight Reinforced Concrete (LRC) Lightweight structural concrete. Lightweight aggregate concretes supplied by lightweight block supplier Malaysia can be used for structural applications, with strengths equivalent to normal weight concrete. The advantage of using lightweight aggregate concrete includes a reduction of dead loads by making savings in foundations and reinforcement.
A lightweight aggregate concrete supplier in Malaysia product the lightweight concrete panel by using the by-products of industrial manufacturing plant such as fly ash from boiler furnace of a power plant. One of the most popular lightweight concrete materials is foam, sometimes also known as polystyrene foam or expanded polystyrene foam (EPS).
They are either a slurry of concrete and foam or made into a sandwich panel. Foam sandwich panels also come into different format either the foam is in between two outer layers of concrete panels or a concrete layer is surrounded by two outer layers of foam. Consult us, as a leading lightweight concrete panel supplier in Malaysia who can provide you supply and install solution for your project.
Reinforced Wall Panels This type of Reinforced Wall Panels is increasing its popularity in Malaysia due to its heat and sound insulation. It internal is usually using polyfoam so supplier in Malaysia will send the polystyrene or expanded polystyrene to the prefab or precast concrete panel manufacturer and use it as inert material for the wall panel. After that, the precast or prefab concrete panel supplier Malaysia will process the foam to make it cut into size or blend into its concrete mixture, depend on the designs by the architect. Blended polyfoam is easily binding with concrete by using special additives to make sure the adhesion of foam and premix concrete, the lightweight Reinforced Wall Panels manufacturer in Malaysia will then send to any construction site in Malaysia and pour into formwork that has been set up, or alternatively by the site contractor. Otherwise, the premix supplier will pour into the mold in their own factory to foam reinforced wall panels, either for a wall, slab, roof or other infrastructure components, send it after it is cured.
Where to Buy Lightweight Blocks and Get Contractor in Malaysia Aathaworld Sdn Bhd supply and install Autoclaved Aerated Concrete Blocks or Reinforced Wall Panels that is applicable for interior and exterior, structural and non-structural lightweight concrete panel (partition wall), staircase, floating building, indoor and outdoor, light and heavy industrial usage, residential, commercial, high rise, industrial, shop lot, home, offices, retreat, hotel, café, to other customizable specification. As an Autoclaved Aerated Concrete Blocks and Reinforced Wall Panels supplier and installer (contractor) in Malaysia, we are able to provide a full-service consultancy, customizable manufacture, supply and install for your project covering new, repair, building refurbishment and renovation projects in KL Kuala Lumpur, Selangor, Klang Valley, JB Johor Bahru, Penang, Malacca (Melaka), Seremban Negeri Sembilan, Perak, Pahang, Kuantan, Kelantan, Terengganu, Perlis, Alor Setar Kedah, as well as Sabah and Sarawak for East Malaysia; of course, also we are able to be lightweight panel supplier and lightweight panel contractor for other countries in Southeast Asia (SEA) such as Philippines, Singapore, Brunei, Cambodia, Vietnam, Laos, Myanmar (Burma), Thailand, Indonesia.
Submit your lightweight or green building materials projects sourcing requirements (supply and install), either you are looking for a supplier or contractor for new or existing lightweight blocks, renovation projects in KL Kuala Lumpur, Selangor or other states in Malaysia. Submit your inquiry to us now at info@aathaworld.com or call (WhatsApp) to +(60)11-7001 1003 (Monday to Friday) or +(60)11-1188 1003 (Saturday, Sunday & Public Holiday).
Photo credit: arrowheadprecast, archiproducts, chinasteelmaterial, kenresearch, exportersindia
Comentarios