Formwork can be temporary, can be permanent mould that assist the concrete or other types of material in shape forming. It is mostly used in forming the wall, slab or structural components such as column and beam. The formwork is assembled and erected, before any watery mixture material is poured. The raw materials for formwork can be made up of timber, steel, aluminium, plastic, engineered formwork is a common name for metal frame material (such as aluminium and steel). Many formworks nowadays are usable, going green and be friendly to the environment are the key responsibilities to the formwork supplier in Malaysia.
Timber formwork supplier in Malaysia manufactures formwork that can have high resistance to the moisture or water, because construction site formworks normally exposed to outdoor weather and waterproofing coating should be painted on the plywood or other types of particleboard to ensure weather-resistant formwork is produced. Plywood formwork used to have shorter lifespan but as technology advances, the timber formwork supplier in Malaysia able to cater for lengthier usage. Low labour cost in Malaysia cause timber formwork supplier Malaysia is doing well, as contractors have a high preference in this type of formwork although it is a labour-intensive formwork.
Most of the metal formwork supplier in Malaysia able to supply aluminium and steel formwork in which these two are the most common one among all other metal formworks. This type of engineered formwork is built on a pre-fabricated basis where the required surface structure will be poured with concrete or other materials. Both steel and aluminium formworks have an obvious undebatable advantage which is the construction speed. Metal formwork supplier in Malaysia will provide modular screw, systems pin and clip together with the framing component to the contractor, assemble and dissemble of the formwork became easier.
Besides fast speed construction in formwork as an advantage for metal formwork, engineered formwork also offer a long life-cycle which translate into lower cost for maintenance and replacement. The covering has high strength, resistant to high load, weather and chemicals. One of the reasons makes the steel and aluminium formwork supplier in Malaysia is more preferable than other types because of its hard-wearing application and the reusability. Some formwork supplier in Malaysia claims that metal formworks can actually being used for more than thousands times.
Reusable formwork is very important to construction nowadays, and luckily there is plenty of reusable formwork supplier in Malaysia who can supply and install for the client. Recyclable formwork comes in also modular and interlocking form, easy to be installed and wide application. These formwork panels also suitable for mass housing project or high rise building as they are strong yet relatively light in weight. Aluminium and plastic formworks in Malaysia give such advantages to the builder, hence, plastic formwork contractor in Malaysia does have a huge market and high product acceptance level compared to other type of materials.
There is another type of formwork which is popular in Malaysia’s construction industry, purposely cater for the mould installation to shape pre-cast component and other materials usage. Permanent formwork can also be an on-site and off-site assembly, the on-site setup is also known as permanent insulated formwork, it is usually applied for one of the Industrialized Building System (IBS) that we called it as insulating concrete form (ICF).
Formwork supplier Malaysia will leave the formwork remains at the original position even after the concrete has been cured. Its main purposes are to provide insulation against sound, thermal, increase the strength, speed as well as creating the space for utility accessories to be pre-installed. ICF works the best with the following designs we mention. First, sandwich panel either the Expanded Polystyrene (EPS) layer is between the concrete, or concrete layer is in between the EPS and of course both ways require formwork support. Furthermore, it can be made up by a mixture of EPS and pre-mix concrete and this is commonly used in the partition wall and slab screed layer.
For off-site mould assembly, formwork is also being used due to its high level of workability. Formwork supplier in Malaysia does supply many to pre-cast concrete factory client for their production, the pre-cast factory put on the formwork as a mould to support and shape whatever precast block, wall panel, slab panel, beam and many more. The formwork mould is erected and installed permanently at the factory for repetitive use (basically it would not be dissembled if not necessary), the concrete or other fluid materials will be poured into the mould until curing, before sending to the construction site for installation.
Moreover, there are also other types of formworks, including flexible formwork, structural formworks such as beam, slab, column, deck, infrastructure and many more. These types of formwork mostly made by plastic, aluminium, HDPE, timber or steel. The formwork supplier in Malaysia is usually specialized into certain material, which makes their product and service more reliable. Aluminium formwork supplier in Malaysia does not usually cross-supply timber or steel formwork, for example. It is important when it comes into selecting the structural formwork supplier because good quality formworks increase the sustainability in strength integrity and surface finishes.
Good formwork supplier in Malaysia can also custom make and supply formwork that is adjustable for its horizontal and vertical length. The flexible formwork should also enable easy handling for even unskilled labour at the construction site, in term of assemble, dissemble and structure modification. It can be as simple as setting up by hand, clipping, pinning, screwing or more. Positioning and relocation are not issue too if the formwork is good enough and supplied by experienced formwork supplier in Malaysia.
Where to Buy Formwork and Get Formwork Contractor in Malaysia
Aathaworld Sdn Bhd supply and install multiple cost saving formwork that can be used for interior and exterior, indoor and outdoor, light and heavy industrial usage, customizable specification for commercial, residential, high-rise, industrial, plant, factory, mass housing, precast, prefab IBS. As a formwork supplier, installer (contractor) in Malaysia, we are able to provide a full service design consultancy, customize supply and install for your project covering new, repair, refurbishment and renovation projects in KL Kuala Lumpur, Selangor, Klang Valley, JB Johor Bahru, Penang, Malacca (Melaka), Seremban Negeri Sembilan, Perak, Pahang, Kuantan, Kelantan, Terengganu, Perlis, Alor Setar Kedah, as well as Sabah and Sarawak for East Malaysia; of course, also we are able to be formwork supplier and formwork contractor for other countries in Southeast Asia (SEA) such as Singapore, Cambodia, Vietnam, Laos, Myanmar (Burma), Thailand, Indonesia, Philippines, Brunei.
Submit your formwork materials projects sourcing requirements (supply and install), either you are looking for a formwork supplier or formwork installer for new or existing formwork replacement, formwork system in KL Kuala Lumpur, Selangor or other states in Malaysia. Submit your enquiry to us today at info@aathaworld.com or call (whatsapp) to +(60)11-7001 1003 (Monday to Friday) or +(60)11-1188 1003 (Saturday, Sunday & Public Holiday).
Photo credit: peri-usa, fofuform, acrow, periph, wikiwand, ergenekoninsaat, perigroup, peri, variantfactory, ateshaniskele
Comments